VPPB45PCA PASSIVE VIDEO+POWER+PTZ BALUN RJ45 JACK – CONVERTS AC TO 12VDC
Discontinued
VPPB45PCA PASSIVE VIDEO, POWER & PTZ BALUN WITH AC-DC CONVERTER (RJ45 JACK)
The main feature of the VPPB45PCA is its ability to convert 24-28VAC to regulated 12VDC at the camera, allowing the system to be highly tolerant of voltage drop in the cable. The VPPB45PCA has a mini-coax pigtail lead which allows quick mounting onto fixed cameras and allows in-camera mounting in most dome cameras. RJ45 jack connection for UTP cable, enabling quick and simple installation. Working in pairs, the VPPB45PCA eliminates costly and bulky coaxial cable, allowing live CCTV colour video signal up to 400m (1300ft), power transmission up to 250m (750ft) and PTZ data up to 200m (600ft).
The superior interference rejection and low emissions of the VPPB45PCA allow signals to coexist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the use of a shared or existing cable infrastructure. The VPPB45PCA has built-in surge suppression to protect video equipment against damaging voltage spikes. Its crosstalk and noise immunity ensure quality video signals.
Example scenarios
The DOSS Range of UTP Video+Power+PTZ Baluns allow you to connect your CCTV system using cheaper, thinner, lighter and more readily available CAT5E cable rather than expensive and bulky RG59U cable.
The passive (non-amplified) baluns allow transmission of realtime CCTV video signals and power over cost-effective Unshielded Twisted Pair (UTP) cable, without any compression, loss or signal degradation and without the need for extra power supplied to be installed. Baseband (composite) signals of any type are supported. Sending camera power over the same twisted pair as video means less cabling, and no power supply required to be installed near to the camera. With PTZ/Data transmission built-in, you can still control all your PTZ cameras and other devices without any extra baluns or cables.
Applications
- Security Monitoring System
- Multimedia Network Teaching System
- Medical Monitoring Display System
- Industrial Automation Control System
- Banking, securities, financial information display system
- Remote Network Server Monitoring
- Department Store Security
- Casino Security
- Hospitals, Airports and banks
- School Campuses
Features
- Single Channel Passive Video, Power & PTZ/Data Transceiver
- Down-converts 24-28VAC to regulated 12VDC
(voltage conversion at video transmitter end only)
- Down-converts 24-28VAC to regulated 12VDC
- Full-motion colour signal up to 400m (1300ft) and
monochrome (B&W) up to 600m (1950ft) via UTP CAT5e/6 - Transmit power signal up to 250m (750ft)
- Transmit data/PTZ signal up to200m (600ft)
- NTSC, PAL & SECAM video format compatible
- Real-time transmission
- Male BNC with extended mini-coax pigtail
- RJ45 Jack
- No power required
- Exceptional interference rejection
- Built-in TVS (Transient Voltage Suppressors) for surge-protection
- Lightning protection design Grade III
- 50dB crosstalk and noise immunity
- Wave Filter Design, Anti-Static Design
- Compact size and easy installation
- ABS engineering plastic housing
Specifications
Applied Devices | CCTV cameras, monitors, DVR, switchers, IP encoders, and other CCTV equipment | |
Video | Video Format | PAL, NTSC, SECAM |
Operating Frequency | DC to 5MHz | |
Max Distance | UTP Category 5e (24AWG) Color: 400m (1300ft) B&W: 600m (1950ft) |
|
Common-mode / Differential-mode rejection |
15kHz to 5MHz 60dB typical | |
Impedance | Coax, Male BNC 75O unbalanced | |
UTP, two coax pigtail 100O balanced | ||
Attenuation | 1.5dB Max typical | |
Wire Type | Network Wiring | One Unshielded Twisted Pair (for each video signal) 24-16 AWG (0.5-1.31mm) |
Category Type | 2 or better | |
Impedance | 100 ±20 ohms | |
DC Loop Resistance | 18O per 100m (52O per 1,000ft) | |
Differential Capacitance | 62 pF/m max (19 pF/ft max) | |
Power | No external power required to operate | |
Power input/output | 24~28VAC input (Video receiver end) 12VDC output (Video transmitter end) |
|
PTZ signal | Transmission distance | Up to 300m (1000ft) via UTP CAT5e/6 |
Connector | Video input/output | Male BNC connector |
Video input/output | 8P8C (RJ45) Jack | |
Protection | Surge Protection | Renewable solid state surge protection |
Video Input | 2KV(common mode), 10/700µs IEC6100-4-5/1955(GB/T 1726, 5-1999) |
|
Video Output | 2KV(different mode), 10/700µs IEC6100-4-5/1955(GB/T 1726, 5-1999) |
|
Mechanical | Housing | ABS engineering plastic |
Body Color | Black | |
Dimensions (L*W*H) | 60.4*29*20.4mm (BNC connector & cable excluded) | |
Net Weight | 65g | |
Environmental | Operating Temperature | -20°~ 70°C |
Relative Humidity | 0~95% (non-condensing) | |
Storage Temperature | -40°~ 150°C |
Reference: Wiring
Video+Power+PTZ Balun wiring
DOSS Video & Power Baluns |
T568A | T568B | |
---|---|---|---|
Pin 1 | Video | White/Green | White/Orange |
Pin 2 | Video | Green | Orange |
Pin 3 | Data + | White/Orange | White/Green |
Pin 4 | Power – | Blue | Blue |
Pin 5 | Power – | White/Blue | White/Blue |
Pin 6 | Data – | Orange | Green |
Pin 7 | Power + | White/Brown | White/Brown |
Pin 8 | Power + | Brown | Brown |
Reference: Voltage Drops
Power over Twisted Pair: Voltage Drop Reference
Transmission Distance |
Transmission Voltage (Voltage Drop) | ||
---|---|---|---|
12VDC/0.5A camera requirement |
12VDC/1A camera requirement |
12VDC/1.5A camera requirement |
|
50m / 160ft | 13.5V (1.5V) | 15.5V (3.5V) | 17.0V (5.0V) |
100m / 320ft | 15.5V (3.5V) | 18.5V (6.5V) | 22.0V (10.0V) |
150m / 500ft | 17.0V (5.0V) | 22.0V (10.0V) | 27.0V (15.0V) |
200m / 650ft | 18.5V (6.5V) | 25.5V (13.5V) | 32.0V (20.0V) |
300m / 1000ft | 22.0V (10.0V) | 32.0V (20.0V) | 42.0V (30.0V) |
eg: to supply a camera that requires 12VDC/0.5A, over a run of 150m cable, you require an initial transmission voltage supply of 17.0VDC (to account for 5V voltage drop over cable) Note: based on typical CAT5e cable (will vary on make and quality of cable) |