Find Product

Select a Category:
All Products > Cables > Speaker > DOHQR AUDIOPHILE SPEAKER CABLE

DOHQR AUDIOPHILE SPEAKER CABLE

Features

  • Square section clear and flexible outer jacket.
  • Tough polyethylene dielectric between the copper conductor and the clear outer jacket ensures optimum interface for higher performance.
  • Unique centre insulated core technology reduces time related distortion, by minimising magnetic fields which are stronger at the centre of the core. This reduces noise and dramatically increases dynamic range.
  • Sold as a 100 metres roll

Specifications

  • DC Resistance: ≤1.5Ω/100m
  • Conductor:2×15.8AWG
  • Filler: 2*Ø0.8mm PE
  • Mid-jacket:2*Ø2.7mm PE
  • Outer Jacket:Ø5.6*9.0mm PVC, transparent.
  • Recommended max run to any HiFi speaker (min 6 ohm) is 10m
Short URL: https://bit.ly/3jhIhBy

 

Speaker Wire Selection Guide

Speaker wire plays an important role in speaker sound quality and reproduction. All speaker wire has some resistance and, over long runs, can affect audio quality. Not only can it reduce signal levels, but it can also affect the signal in a non-linear fashion, affecting different frequencies different amounts. This effectively changes the frequency response of your audio system in an unpredictable manner.

By following a few simple guidelines, you can reduce this effect without spending a fortune on expensive cable.

Gauge / Diameter

AWG Diameter Suggested DOSS Cable Max Recommended Run
for Front Speakers		 Max Recommended Run
for Surround Speakers**
4Ω 6Ω 8Ω 4Ω 6Ω 8Ω
22 0.64 mm   1.9 m 2.7 m 3.6 m 3.2 m 4.6 m 6.1 m
20 0.81 mm 2X30-.14M 3.1 m 4.6 m 6.1 m 5.3 m 7.8 m 10.4 m
18 1.02 mm 2X41-.16,
4X30-.10		 4.9 m 7.3 m 9.8 m 8.3 m 12.4 m 16.7 m
16 1.29 mm 2X91-.12,
2X96-.12,
DOHQ		 7.3 m 10.9 m 14.6 m 12.4 m 18.5 m 24.8 m
14 1.63 mm   12.2 m 18.3 m 24.4 m 20.7 m 31.1 m 41.5 m
12 2.05 mm 2X308.12R 18.3 m 27.4 m 36.6 m 31.1 m 46.6 m 62.2 m

Values for other gauges can be found here: Wikipedia: American wire gauge
** A greater tolerance is allowed for Subwoofers and Surround speakers where accuracy of frequency response is not as critical.

Bi-wire

Instead of running a large gauge wire (ie 10+ AWG), double up lengths of a smaller gauge to double the distance. For example:

  • Instead of 10AWG to reach 60m, use two lengths of 12AWG wired in parallel to double the recommended distance
  • Use 4-cores of 16AWG to achieve 20m run; 2-cores for (+), 2-cores for (-)

Twist, don’t shield

Any EMI that maybe induced in speaker wires is often below standard noise levels and as such, very little is required to protect the signals from interference. However over longer runs, particularly where speaker wires are run physically parallel with power cables for significant distances, EMI may be an issue. It is recommended to uses twisted wires to reduce EMI as shielding or braiding can create a capacitance component to the dynamic resistance of the cable, undoing all your work in picking the correct gauge wires and affecting the frequency response of your system in a very unpredictable manner.

Short URL: Generating...